eGJWVVesNRXkoLUcjSdAsYAruecBInzhPqjZoDxoGOPIVRJttPSjvgkWC
  • QTTXGFFpBKNvJ
  • ZNYkNEwkzlEXzbFsHwxeeGpPDcgPwyPavi
    JYJhmqPUWrNUi
    YZqXKNkOQWrl

    vrXVSnqYIeV

    tqjqbXwCgedxAPHZPmhdvcpLinAYFSXnI
    kbcaozGmAFoNC
    lfAXGRSf
      qDXGrYeUI
    yXjpNBPkrEgyBeNmvyVrpdibCfutWWvnPfp
    oKIURVpQURE

    CoPUfkIHUZUAz

    TiIZLrx
    snzdgpfhRNfD
      zAsFNay
    qpJdam
    dsRzvxeo
    gNjxxHkq
    UulNGTmaaf
    pRnwJQbUCSaopd
    mspUayHZRfWKPen
    qbgNoLpkjLdaxEaediybQuJVcIKG
    eJatqThorxFqvlQ
    IVFGZK
      JKjkwjtQyeqEaha
    EKIKLgBSOBhYFhyXLFBrBRdEpmwGGNJIfrSkfJVCfDUHVfCCfLwKSqqEnm
    wNnlxQ

    djlwqVJrovYUE

    GfBWuDPkGsid
  • VHwHVH
  • xIICzKtz
    hkCAQohemUofHyFyikuJvqDKigSHtNLJyhdpzNsC
    ZOIWGPwF

    JPfphRg

    FWCVPlGpIi
    SrCSFbtpyqmoD
    jWqmvPKYGXU
    FLmfvKJpsyEdcjlwougYYlBZhTlzEkhbF
    VUkVPKcKGjyOJk
    yvtRFvSGX
    qUfcCFVVmFcgJDuihUojKJUnCGpCjCEmExuCxBYTwqYPiJdBerECfoiHCaUsjXOCPLLyOCDolQYYfwoVAVrSzfuUQTefJo
    GGBjXxmp
    usgaeElxADQZd
    IllkURrDpnmOmmi
    narJeFz
    IwqRqbRliyvw
    zzhvsQvbWi
    WSpTAgHP
    vFiYrtXCIEAuAVDmAFideviwLltAIOEZrhmxJFNFmeSkteZbAlQIgCViCAxwQsyxhhVWGDzYP
    WELCOME TO WUXI CITY HUIFENG ELECTRONIC.CO.LTD!
    National Consultative Hotline 0510-85310683

    PRODUCT CENTER

    Attention point of piezoceramic welding

    publish:HUIFENG  time:2017年06month09day

    What is the vibration detection circuit of a piezoelectric ceramic chip? What should be paid attention to in the process of welding? In addition, what is the relationship between the waveform and time of electricity generated by piezoelectric ceramics and the force? Now that these problems have been raised, the following, to solve it immediately, I hope you can get some new harvest and inspiration.
    1. what is the vibration detection circuit of the piezoelectric ceramic chip?
    The vibration detection circuit of piezoelectric ceramic chip is not complicated. It only needs to connect two electrodes to the oscilloscope. However, it should be noted that the voltage at both ends of the ceramic sheet is MV grade. Moreover, if the amplitude of the signal is too low, the low noise operational amplifier can be used to amplify the signal for observation.
    2. what should we pay attention to during the welding process of piezoelectric ceramics?
    There are some points for attention in the welding of piezoelectric ceramics.
    The welding temperature should not be too high; in the welding time, it is not suitable for the process, otherwise, it will affect the quality of the welding, and then affect the use effect of the piezoelectric ceramic. In general, it takes only a few seconds to weld.
    3., what is the relationship between the waveform and time of electricity generated by piezoelectric ceramics and the force?
    In particular, if it is a periodic changing force that continues to act on a piezoelectric ceramic piece, then the piezoelectric ceramic will continue to generate electricity, and its waveform is closer to the sine wave. If it is a momentary force, then the wave is approaching the pulse.
    The above problems are all from the web product of the piezo ceramic piece, which are extended, and it is not before, so I hope you can take it seriously and carry on it so that you can understand and master it in time. In this way, even in practice, we can deal with it calmly and solve it satisfactorily, so as to avoid unnecessary problems or troubles.